Search Results

Search Again
Page 1 of 10
  1. PaulBeinert
    Post

    Los Angeles Junction PLAN, & MAPS

    Which cad program are you going to use? I use AnyRail
    Post by: PaulBeinert, Apr 12, 2016 in forum: Layout Design Discussion
  2. PaulBeinert
    Post

    Vista failing, Still using old JMRI software - upgrading to Win7

    I belong to the Yahoo JMRI group and in preferences I have it set to send me summaries, I then have a filter setup in email to put the JMRI emails...
    Post by: PaulBeinert, Jan 19, 2016 in forum: DCC & Electronics
  3. PaulBeinert
    Post

    Vista failing, Still using old JMRI software - upgrading to Win7

    Johnny, There should be a button to start a new conversation but if not, you may not be logged in. Either way, you should be able to search and...
    Post by: PaulBeinert, Jan 10, 2016 in forum: DCC & Electronics
  4. PaulBeinert
    Post

    test wiring on new layout?

    Ignoring the fact that I now need to pull out my meter and validate what readings I get ... Your turnouts could cause shorts when thrown so test...
    Post by: PaulBeinert, Jul 23, 2015 in forum: DCC & Electronics
  5. PaulBeinert
    Post

    Auto reverse circuit for G Scale layout

    Will the PSX-AR work for G scale? http://www.dccspecialties.com/products/pdf/man_psxar.pdf
    Post by: PaulBeinert, Jul 15, 2015 in forum: DCC & Electronics
  6. PaulBeinert
    Post

    Count of Posts by User

    So now it takes two clicks to see the count where before it was already visible. That is a step backwards
    Post by: PaulBeinert, Jul 15, 2015 in forum: Support
  7. PaulBeinert
    Thread

    Count of Posts by User

    What happened to the post counts that showed up under peoples names and information? I really liked being able to tell who was active and who was...
    Thread by: PaulBeinert, Jul 12, 2015, 20 replies, in forum: Support
  8. PaulBeinert
    Post

    Auto Reversing section goes dead

    Danny, Did lowering the trip level help?
    Post by: PaulBeinert, Jul 12, 2015 in forum: DCC & Electronics
  9. PaulBeinert
    Post

    DCC for Dummies

    Was this the Sticky post that got unstuck?
    Post by: PaulBeinert, Jun 17, 2015 in forum: DCC & Electronics
  10. PaulBeinert
    Post

    Auto Reversing section goes dead

    Danny, Which lights are flashing on the PSX-AR when you enter the reversing loop from the top and and then which lights flash when entering...
    Post by: PaulBeinert, Jun 14, 2015 in forum: DCC & Electronics
  11. PaulBeinert
    Post

    Triple Crossing, Richmond, VA?

    Where in Richmond?
    Post by: PaulBeinert, Jun 13, 2015 in forum: N Scale
  12. PaulBeinert
    Post

    Digitrax PM42 vs. DCC Specialties PSX-4

    LnRrr, Post # 5 on the first page shows how I daisy chained PSX's and PSX-ARs
    Post by: PaulBeinert, Jun 13, 2015 in forum: DCC & Electronics
  13. PaulBeinert
    Post

    Auto Reversing section goes dead

    Danny, Do you have a diagram of the reversing loop and all turnouts within in it?
    Post by: PaulBeinert, Jun 13, 2015 in forum: DCC & Electronics
  14. PaulBeinert
    Post

    Digitrax PM42 vs. DCC Specialties PSX-4

    I mounted my boards with 3/4" nylon tubes to allow more air flow between the PSX and the plywood.
    Post by: PaulBeinert, Jun 10, 2015 in forum: DCC & Electronics
  15. PaulBeinert
    Post

    My only guess is that it's driven by dollars....

    I have 24 Peco Electrofrogs and have not done any changes to them other than removing the springs when I Installed my Tortoises. I have zero power...
    Post by: PaulBeinert, Jun 4, 2015 in forum: DCC & Electronics
  16. PaulBeinert
    Post

    Overanalyzing

    Shifty, With DCC, it doesn't matter that the yard is within the power block of the reversing loop.
    Post by: PaulBeinert, May 19, 2015 in forum: N Scale
  17. PaulBeinert
    Post

    NCE PowerCab and Bachmann Loco Oddity

    Have you cleaned the contacts? Sounds like intermittent power issue ...
    Post by: PaulBeinert, May 18, 2015 in forum: DCC & Electronics
  18. PaulBeinert
    Post

    DC/DCC Wiring

    Don, As I do not have any of these components, I am not sure how it would all connect. If I find some downtime, I will locate the documentation...
    Post by: PaulBeinert, May 16, 2015 in forum: DCC & Electronics
  19. PaulBeinert
    Post

    Overanalyzing

    Shifty, I do not see any reversing loops in that diagram.
    Post by: PaulBeinert, May 12, 2015 in forum: N Scale
  20. PaulBeinert
    Post

    DC/DCC Wiring

    Don, Have you implemented this yet?
    Post by: PaulBeinert, May 9, 2015 in forum: DCC & Electronics
Showing results 1 to 20 of 196 Next >
Search Again
Page 1 of 10