Search Results

Search Again
Page 1 of 6
  1. jshglass
    Post

    Question Advice

    Thanks for the tips, everyone! I fiddled with a bunch of different things, even plaster, but a few weeks ago I found that CMR 3D prints the C18...
    Post by: jshglass, Aug 16, 2019 in forum: Z Scale
  2. jshglass
    Post

    Question Advice

    Thanks, Mark. I’m not going to worry so much about the rounded corners at this point. I figured I could sand them down enough that the small size...
    Post by: jshglass, Jun 10, 2019 in forum: Z Scale
  3. jshglass
    Thread

    Question Advice

    Hey everyone, Longtime no post. Been getting back into the layout slowly, but surely. Next big task is to create an Ann Arbor style caboose in Z...
    Thread by: jshglass, Jun 10, 2019, 13 replies, in forum: Z Scale
  4. jshglass
    Post

    Alco S2

    Excellent! Ann Arbor used these. I was going to get an SW1200, paint it up in AAR colors, and ignore the historical inaccuracy, but this changes...
    Post by: jshglass, Jun 3, 2019 in forum: Z Scale
  5. jshglass
    Post

    Micron Art status

    Bummer. I bought his box girder bridge. What a joy to assemble for my novice hands. Really got my excitement up and running to construct the rest...
    Post by: jshglass, Jan 29, 2019 in forum: Z Scale
  6. jshglass
    Post

    Atlas switches

    When you get a chance, do you mind posting a quick review? Also, are there any good videos out there explaining how to wire an Atlas turnout? I’m...
    Post by: jshglass, Jan 7, 2019 in forum: Z Scale
  7. jshglass
    Post

    Z scale 250 ton Industrial Brownhoist crane

    Link to your Shapeways page so we can order? This is awesome!
    Post by: jshglass, Dec 12, 2018 in forum: Z Scale
  8. jshglass
    Post

    Dear Micro-Trains wish you would make:

    I would buy that AA caboose in a New York minute! Are you asking for them to make it in Z or N? Looking for someone who’s good with custom Z paint...
    Post by: jshglass, Oct 28, 2018 in forum: N Scale
  9. jshglass
    Post

    Marklin modern signal tower kit-bash

    :eek::eek::eek::eek::eek::eek::eek::eek::eek::eek:
    Post by: jshglass, Oct 23, 2018 in forum: Z Scale
  10. jshglass
    Post

    Small scale Z manufacturers

    What a great thread idea, Mark. Thanks for starting this. Those little motorcycles are great! Might have to pick up a set.
    Post by: jshglass, Oct 23, 2018 in forum: Z Scale
  11. jshglass
    Post

    T Gauge SD70ACe

    So cool! Any videos of it running?
    Post by: jshglass, Oct 18, 2018 in forum: T Gauge
  12. jshglass
    Post

    my module layout

    This is so cool! What a great feat of automation engineering! :)
    Post by: jshglass, Oct 12, 2018 in forum: Z Scale
  13. jshglass
    Post

    Help! MTL Turnout Issue

    I’m putting an end to this thread. I just took the turnouts apart and cleaned every surface I could find. Tested again with a continuity meter and...
    Post by: jshglass, Oct 12, 2018 in forum: Z Scale
  14. jshglass
    Post

    Help! MTL Turnout Issue

    Is there a fix for that? Sent from my iPhone using Tapatalk
    Post by: jshglass, Oct 7, 2018 in forum: Z Scale
  15. jshglass
    Post

    Help! MTL Turnout Issue

    Just on the switch. It goes through the straight just fine. Here’s a picture of it and how things are wired.[IMG] Sent from my iPhone using Tapatalk
    Post by: jshglass, Oct 7, 2018 in forum: Z Scale
  16. jshglass
    Post

    Help! MTL Turnout Issue

    Yes. Two MTL turnouts to to crossover between to straights. Sent from my iPhone using Tapatalk
    Post by: jshglass, Oct 5, 2018 in forum: Z Scale
  17. jshglass
    Post

    Help! MTL Turnout Issue

    So I replaced the insulated joiners with nickel/silver joiners. Instead of stalling out, the loco shorts out. Both blocks are set to the same cab,...
    Post by: jshglass, Oct 5, 2018 in forum: Z Scale
  18. jshglass
    Post

    Help! MTL Turnout Issue

    Holy crap, man! You just blew my mind. I had no idea I could do that. I feel dumb now. Will test it out tomorrow. Sent from my iPhone using...
    Post by: jshglass, Oct 4, 2018 in forum: Z Scale
  19. jshglass
    Post

    Help! MTL Turnout Issue

    So do you think if I boost this section of track that would help? It currently is not powered for some reason, which is what I think my problem is.
    Post by: jshglass, Oct 4, 2018 in forum: Z Scale
  20. jshglass
    Post

    Help! MTL Turnout Issue

    Sorry, I was not clear. This section of track is not fed from the adjoining turnout because it is joined with insulated joiners. The two joining...
    Post by: jshglass, Oct 4, 2018 in forum: Z Scale
Showing results 1 to 20 of 120 Next >
Search Again
Page 1 of 6