Bottle Brush Tree Maker

A devise I made to make realistic looking pine trees. Each tree costs me about .50 cents.

Filters:

Type:
Image Uploads x
Remove All Filters:
x
Sort By: Date

Sort By...

Filters

Type Filters

7th) Let paint dry & use any spray adhesive and spray the brown bare tree. place into a container of your choice of ground foam (I used connifer green) put lid on and shake side to side a few times. Remove tree and shake of a few times.
Brucead

Brucead

Bottle Brush Tree Maker
0 x

7th) Let paint dry & use any spray adhesive and spray the brown bare tree. place into a container of your choice of ground foam (I used connifer green) put lid on and shake side to side a few times. Remove tree and shake of a few times.

0
192
1
0
24 Jan 2011
6th) Then use automotive primer brown & spray paint the entire tree.
Brucead

Brucead

Bottle Brush Tree Maker
0 x

6th) Then use automotive primer brown & spray paint the entire tree.

0
191
0
0
24 Jan 2011
5th) Take scisors and start from the top trim the tree. Short on top & fat on the bottom. Then Melt down hot glue stics in an old pot, then dip the trunks into hot glue & allow exsess glue to drip off, then place tree in cold water to harden the hot glue.
Brucead

Brucead

Bottle Brush Tree Maker
0 x

5th) Take scisors and start from the top trim the tree. Short on top & fat on the bottom. Then Melt down hot glue stics in an old pot, then dip the trunks into hot glue & allow exsess glue to drip off, then place tree in cold water to harden the hot glue.

0
232
0
0
24 Jan 2011
4th) Cut the the trees out leaving about 1" for the trunks.
Brucead

Brucead

Bottle Brush Tree Maker
0 x

4th) Cut the the trees out leaving about 1" for the trunks.

0
210
0
0
24 Jan 2011
3rd) Now, crank your handle about 40-60 cranks making the wire very tight with rope strands inserted. once tight, the strands will never come out.
Brucead

Brucead

Bottle Brush Tree Maker
0 x

3rd) Now, crank your handle about 40-60 cranks making the wire very tight with rope strands inserted. once tight, the strands will never come out.

0
253
0
0
24 Jan 2011
2nd) Thread the 16gage wire into each of the 2 eye bolts, use pliers to trwist the wire ends. Then crank the handle 6 times to lightly twist wire together. Cut you rope into 2" sections. Insert rope between the wires & spread out evenly.
Brucead

Brucead

Bottle Brush Tree Maker
0 x

2nd) Thread the 16gage wire into each of the 2 eye bolts, use pliers to trwist the wire ends. Then crank the handle 6 times to lightly twist wire together. Cut you rope into 2" sections. Insert rope between the wires & spread out evenly.

0
267
0
0
24 Jan 2011
1st) I made this devise to twist rope strands between 2 16gage wires. 2 1/4" eye bolts 1 @ 1.5" long and 1 @ 5" long drill a hole in the wood. Bolt on the short eye bolt so it will not move. The longer eye bolt must be bolted on so it can freely turn. Make a handle with scrap wood and put a 6" bolt in the opposite end. This will be the crank handle.
Brucead

Brucead

Bottle Brush Tree Maker
5.00 x

1st) I made this devise to twist rope strands between 2 16gage wires. 2 1/4" eye bolts 1 @ 1.5" long and 1 @ 5" long drill a hole in the wood. Bolt on the short eye bolt so it will not move. The longer eye bolt must be bolted on so it can freely turn. Make a handle with scrap wood and put a 6" bolt in the opposite end. This will be the crank handle.

0
332
0
1
24 Jan 2011
Brucead, Jan 24, 2011
    There are no comments to display.