Search Results

Search Again
Page 1 of 4
  1. ritafritz
    Post

    Opinions on a custom painting question

    Nothing wron with that paint job. SWEET!!!!!!
    Post by: ritafritz, Feb 3, 2005 in forum: N Scale
  2. ritafritz
    Post

    SP Halloween Scheme

    Ibeleive that some of the SP & Cotton Belt RS3's were painted in Haloween colors.
    Post by: ritafritz, Feb 1, 2005 in forum: N Scale
  3. ritafritz
    Post

    Finally I can ask a question about engines!

    I place little solvaset on the numbers. After a minute or two I carefully remove the numbers with a pencil eraser. Rub lightly. You may need...
    Post by: ritafritz, Jan 31, 2005 in forum: The Inspection Pit
  4. ritafritz
    Post

    Conrail SD-40-2's and Dash-8's

    The SD38 and 38-2's did NOT have large porches. Only the SD40-2's did. They were on SD45 frames which wre longer accounting for the long porch....
    Post by: ritafritz, Jan 28, 2005 in forum: N Scale
  5. ritafritz
    Post

    Dummy Engines

    I used a dummy Trix F7B as a heating/power car for myMOW/Wreck trains.
    Post by: ritafritz, Jan 27, 2005 in forum: N Scale
  6. ritafritz
    Post

    how about some high and wide loads!!!!

    Great paint job!!!. Usual speed for a car like that is 15 MPH. Really slows down other traffic, gets out of the way of EVERYTHING. Whoever is...
    Post by: ritafritz, Jan 25, 2005 in forum: N Scale
  7. ritafritz
    Post

    SP Kato Engines

    I have all kind I want to trade for undecs. Email me offline and I'll send you a list.
    Post by: ritafritz, Jan 16, 2005 in forum: N Scale
  8. ritafritz
    Post

    Shays Down - Count

    PowerSteamGuy1790: Whiat decoder did you use in your shay, where was it placed and please detail the installation procedure.
    Post by: ritafritz, Jan 14, 2005 in forum: N Scale
  9. ritafritz
    Post

    LL GP-18/20/38-2 + DCC = ????

    See the attached web site for instructions on placing decoders in these engines. http://www.trainweb.org/nrmrc/dcc/conversions.html
    Post by: ritafritz, Jan 13, 2005 in forum: DCC & Electronics
  10. ritafritz
    Post

    Decoder for a Kato SD45

    Use the Aztec milled frame and a Digitrax DN163A0 decoder. Look for the Kato SD40/45 in the following link....
    Post by: ritafritz, Jan 12, 2005 in forum: DCC & Electronics
  11. ritafritz
    Post

    Decoders for Atlas N GP9 Phase 2 and GP9TT

    The link to the Aztec site is: http://www.aztectrains.com/pages/DCCFrames.html
    Post by: ritafritz, Jan 12, 2005 in forum: DCC & Electronics
  12. ritafritz
    Post

    Decoders for Atlas N GP9 Phase 2 and GP9TT

    Loco1999: Yep they sure do. Check their website. Its $10.00 for each frame. NOTE: Due to 20 feet of snow in the Sierra Nevada Mtns. your...
    Post by: ritafritz, Jan 12, 2005 in forum: DCC & Electronics
  13. ritafritz
    Post

    Decoders for Atlas N GP9 Phase 2 and GP9TT

    $10.00 for an Aztec frame and the cost of the decoder. About 35.00
    Post by: ritafritz, Jan 12, 2005 in forum: DCC & Electronics
  14. ritafritz
    Post

    Decoders for Atlas N GP9 Phase 2 and GP9TT

    nscale_lover: It does not say on the box. Ebay has some for sale. The seller says NO DCC. So i wonder if they came dcc ready.
    Post by: ritafritz, Jan 12, 2005 in forum: DCC & Electronics
  15. ritafritz
    Post

    Decoders for Atlas N GP9 Phase 2 and GP9TT

    That is I am trying to find out. I see a pc board/light board under the top of the frame. It has a split frame.
    Post by: ritafritz, Jan 11, 2005 in forum: DCC & Electronics
  16. ritafritz
    Thread

    Decoders for Atlas N GP9 Phase 2 and GP9TT

    What is the correct decoder for the Atlas N GP9 Phase II and GP9 TT engines?
    Thread by: ritafritz, Jan 11, 2005, 12 replies, in forum: DCC & Electronics
  17. ritafritz
    Post

    Walther's Blast Furnance

    The rolling mill runs 11" long by 71/2" wide.
    Post by: ritafritz, Jan 9, 2005 in forum: HO Scale
  18. ritafritz
    Post

    Sugar beet loads

    Try mustrd seed. Light brown, round and just about the right size for N scale. Try a wash of medium bronw over them after they are on the foam.
    Post by: ritafritz, Jan 9, 2005 in forum: N Scale
  19. ritafritz
    Post

    Atlas MP15's

    The Golden State RR will purchase 2 o each version for its yard jobs. YIPS, there goes my xmas money!!!.
    Post by: ritafritz, Dec 30, 2004 in forum: N Scale
  20. ritafritz
    Post

    How do you measure pulling power?

    I measure min by the weight (in grams) of the cars that an engine can pull over the various ruling grades on my railroad. If an 9-44 can pull 200...
    Post by: ritafritz, Dec 30, 2004 in forum: N Scale
Showing results 1 to 20 of 68 Next >
Search Again
Page 1 of 4